Latest activity

What's new New posts New profile posts Latest activity
  • Bob Hedgecutter
    Bob Hedgecutter replied to the thread Homelite Super2.
    Have you pressure tested the carb to be sure the new needle you fitted is fitting the seat and actually cutting off fuel? Blocked tank...
  • F
    Frank D replied to the thread Homelite Super2.
    Thanks Bob. I have seen that on some after market kits. This diaphragm is correct. I've had it apart 4 times. Checked needle hight...
  • Bob Hedgecutter
    Bob Hedgecutter replied to the thread Homelite Super2.
    Some aftermarket kits- the wee nub on the bottom of the diaphragm is WAY too long, so when assembled it holds the needle open- so the...
  • F
    Frank D posted the thread Homelite Super2 in Chainsaws.
    I've been struggling with an older Super2. Went through the whole saw. Ultra sonic cleaned the carb. It's a Walbro HDA. It will start 3...
  • C
    Clevy60 reacted to Bob Hedgecutter's post in the thread Vevor top handle upgrades?? with Like Like.
    Knock off of a Zenoah. They are what they are- cheap small light work saws- not sure they are worth modification of "improvement"
  • Bob Hedgecutter
    Bob Hedgecutter replied to the thread Vevor top handle upgrades??.
    Knock off of a Zenoah. They are what they are- cheap small light work saws- not sure they are worth modification of "improvement"
  • C
    Clevy60 posted the thread Vevor top handle upgrades?? in Chainsaws.
    Hey guys, I just picked up the small Vevor 25 cc top handle saw I believe it’s the CN-25. I was curious if anyone has one and if they’ve...
    • IMG_7869.jpeg
    • IMG_7871.jpeg
    • IMG_7870.jpeg
  • J
    jpilk99 reacted to Bob Hedgecutter's post in the thread Husqvarna 357XP with Like Like.
    "Classic hose clamp" is not the best option either- they are a bit large and stiff to do the job well and the tightening gear is bulky...
  • R
    rainman74 reacted to Bob Hedgecutter's post in the thread Could chainsaws be safer? with Like Like.
    Chainsaws are not unsafe! Until you add the human content of the equation. Then, they can still be safe as houses- or a ticking...
  • Bob Hedgecutter
    Bob Hedgecutter replied to the thread Husqvarna 357XP.
    "Classic hose clamp" is not the best option either- they are a bit large and stiff to do the job well and the tightening gear is bulky...
  • J
    jpilk99 replied to the thread Husqvarna 357XP.
    Thanks again, Bob. I agree that (I believe) this issue is that the boot is not fully seated. I did, to the best of my ability, make...
  • J
    jpilk99 reacted to Bob Hedgecutter's post in the thread Husqvarna 357XP with Like Like.
    Cannot say I have ever run into this issue- what top end are you using? If an Amazon special it might be in the angle of the intake...
  • Bob Hedgecutter
    Bob Hedgecutter replied to the thread Husqvarna 357XP.
    Cannot say I have ever run into this issue- what top end are you using? If an Amazon special it might be in the angle of the intake...
  • J
    jpilk99 replied to the thread Husqvarna 357XP.
    Do I put the boot on AFTER I've bolted the head back on? (not sure there's enough room to slide it into place)....
  • J
    jpilk99 replied to the thread Husqvarna 357XP.
    Hi again. I had to get a new piston & head, and have everything most of the way back together (haven't done the new crank seal yet) and...
    • IMG_9169.jpeg
    • IMG_9166.jpeg
Show older items
Back
Top